Zoom Boom Telehandler

In order to ensure the stability of the load, the forks should be postioned

At least 18" apart

Under the center of gravity of the load, and spread far enough apart to ensure the load does not become unbalanced

2' apart

As long as the forks are under the center of gravity of the load the width of the forks does not matter

Correct! Wrong!

Machine inspections shall be performed:

Once daily

Weekly

Only when indicator lights are on

Monthly

Before each shift

Correct! Wrong!

Its an acceptable practice to use the forks or attachments to pry wedged or frozen loads free

True

False

Correct! Wrong!

According to OH&S, training is not required to operate zoom booms/telehandlers with a capacity under 10,000 pounds

True

False

Correct! Wrong!

How is a radius measured using a forklift?

From the face of the back rest to the center of gravity of the load

From the front face of the front tire to the center of gravity of the load

From the face of the back rest to the center of the load

From the center of the front tire to the center of gravity of the load

Correct! Wrong!

Before start-up or machine operation, the operator must learn the location and purpose of the:

Controls

Instruments

Indicator lights

Safety and instruction labels

All of the above

Correct! Wrong!

The operator has just placed a load at a 20 foot elevation. In order to remove the forks from under the load, what functions must be done in combination?

Scope in while booming up

Scoping in while booming down

Scope out while booming down

Scope out while booming up

Correct! Wrong!

If the engine fails to start within 30 seconds release the key, wait at least ___ minutes to allow the starter motor to cool before trying again.

1

2

5

10

Correct! Wrong!

The boom and attachments should be lowered to the ground before exiting the machine

True

False

Correct! Wrong!

What is the following symbol?

Center of Gravity

Load Center

Correct! Wrong!

If a signal person is required, they should position themselves:

beside the operators cab

in full view of the operator

in full view of the load

in full view of the operator and load

Correct! Wrong!

When travelling downhill with a load, to ensure machine stability, the operator should travel:

forward, with the load facing downhill

backward, with the load facing uphill

Correct! Wrong!

Who is responsible for the safe operation of the machine?

Owner

Site Supervisor

Foreman

Operator

Site Safety

Correct! Wrong!

While refueling the machine its acceptable to leave the engine running

True

False

Correct! Wrong!

Always bring the machine to a complete stop before reversing the transmission control lever. Failure to do so can result in damage to the load, the machine and/or bystanders

True

False

Correct! Wrong!

When getting on and off the machine, face the machine, use the steps and handrails provided, and always maintain a three point contact

True

False

Correct! Wrong!

It is not necessary to wear the seat belt while operating the machine if your speed is 10kms or less

True

False

Correct! Wrong!

Can the operator exit the machine with a load raised?

Yes

No

Yes, as long as they have full view of the controls.

Correct! Wrong!

Coolant level can be checked safely with the engine at operating temperature.

True

False

Correct! Wrong!

Operator’s shall comply with the requirements of the Occupational Health and Safety Act (OHSA) Applicable Legislation and Company specific policies and procedures

True

False

Correct! Wrong!

The majority of forklifts load charts are based on the center of gravity of the load being ___ feet from the back rest

1'

2'

2.5'

3'

Correct! Wrong!

Before changing steering modes, in what position should you position the front tires?

Does not matter

Straight

To the left

To the right

Correct! Wrong!

When performing work on the hydraulic system:

Lower the boom to a horizontal position

Support the boom with supports or braces

Shut down the engine

Relieve all pressure before disconnecting lines

Ensure all connections are tight before applying pressure

Repair or replace any damaged line, hose or fitting before applying pressure

All of the above

Correct! Wrong!

The operator should ensure that the load is carried:

high, with the forks as close to horizontal as possible

high, with the load centered on the forks with the backrest tilted slight back

low, with the load against the backrest with the backrest tilted slightly back

low, with the load against the backrest with the backrest tilted slightly forward

Correct! Wrong!

The higher the load is raised, the more ______ the machine can become

Unstable

Stable

Correct! Wrong!

If the load obscures the view of the path of travel, the operator should:

raise the load higher until their travel path becomes clearly visible

drive the machine in reverse

Correct! Wrong!

Stan Peterson @xmfg.com

Correct! Wrong!

Zoom Boom Telehandler

In order to ensure the stability of the load, the forks should be postioned

Machine inspections shall be performed:

Its an acceptable practice to use the forks or attachments to pry wedged or frozen loads free

According to OH&S, training is not required to operate zoom booms/telehandlers with a capacity under 10,000 pounds

How is a radius measured using a forklift?

Before start-up or machine operation, the operator must learn the location and purpose of the:

The operator has just placed a load at a 20 foot elevation. In order to remove the forks from under the load, what functions must be done in combination?

If the engine fails to start within 30 seconds release the key, wait at least ___ minutes to allow the starter motor to cool before trying again.

The boom and attachments should be lowered to the ground before exiting the machine

What is the following symbol?

If a signal person is required, they should position themselves:

When travelling downhill with a load, to ensure machine stability, the operator should travel:

Who is responsible for the safe operation of the machine?

While refueling the machine its acceptable to leave the engine running

Always bring the machine to a complete stop before reversing the transmission control lever. Failure to do so can result in damage to the load, the machine and/or bystanders

When getting on and off the machine, face the machine, use the steps and handrails provided, and always maintain a three point contact

It is not necessary to wear the seat belt while operating the machine if your speed is 10kms or less

Can the operator exit the machine with a load raised?

Coolant level can be checked safely with the engine at operating temperature.

Operator’s shall comply with the requirements of the Occupational Health and Safety Act (OHSA) Applicable Legislation and Company specific policies and procedures

The majority of forklifts load charts are based on the center of gravity of the load being ___ feet from the back rest

Before changing steering modes, in what position should you position the front tires?

When performing work on the hydraulic system:

The operator should ensure that the load is carried:

The higher the load is raised, the more ______ the machine can become

If the load obscures the view of the path of travel, the operator should:

Sign up

Login